Home > Error Code > Hot Tub Error Codes

Hot Tub Error Codes

Contents

When the water is not flowing it should be OPEN, not CLOSED, if it is closed replace it. Thank you! Problem 2 LF low flow at certain times with no heat, and a dry warning, not sure what that means, but doesn't sound good. The impeller is spinning in the pump, flow into the tub seems to be pretty low. have a peek here

Then power the system back up, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off. I know we just recently replaced the screen cause it went out just don't know why it keeps shutting down, to the point we have to turn off the main power Please advise...Hottubber Logged Ruby Full Member Posts: 191 Marquis Epic Re: My Marquis SA Reward « Reply #13 on: February 01, 2005, 08:43:23 PM » Well I have the 2004 Also try it this way, Unplug the wires from the pressure switch/flow switch, turn on the pump and then jump the wires.

Hot Tub Error Codes

The filter is clean and both pumps run and the flo switch is new. Posted in:hot tubs and spasspa troubleshooting See more Prev:In-ground Pool Installation Pictures Rowley, MA Back: All Posts Next:In-ground pool building permits, setbacks, and building codes About the Author JayB Jay is You could try jumping out the leads where the pressure switch/flo-sensors plug into the board and see if the heater will click on.

Pump one is two speed, which is also the circulation pump, well maybe not, seems it would then be a three speed cause it also runs for heat at slow speed. NOTE: Temperature sensors should be mounted in a sensor mount in the wall of the spa and not behind the shield on the heater manifold with the hi limit sensor. I replaced the temp sensors but still get the error. How To Fix Flo Error Hot Tub And last, when I try to turn on pump 2 it starts pump one but at a level where there is no pumping action only a hum and the pump sign

Any ideas? Balboa Hot Tub Error Codes I am a hardcore DIY, so is it time to start taking lines apart, which will begin to teach me things, plus I assume I will have to get a new I turned off the GFI, waited a couple of moments, and the same thing occurred. Number two pump still inop.

We'll see if that is the problem.Something just dawned on me. Great Lakes Hot Tub Error Codes See M7 Sensors here. I replaced the mother board twice, the motor and wet end, I've tried 3 new flow switches, new filter, new topside control, new hot and cold sensors. These parts are easily and inexpensively replaced.

Balboa Hot Tub Error Codes

I assumed since my daughter was in the tub with her friend, she set the temp too high and that turned it off. o.k. 3 questions. 1.)Do they get THAT dirty that fast? Hot Tub Error Codes I will keep a close eye on this- Hopefully it's not a sensor problem. Marquis Hot Tub Error Codes I be the PC board needs to be replaced. -Jay admin October 10, 2015 at 7:34 pm Hi Pete, Sounds like either bad sensors or a bad PC board. -Jay admin

The power of the jets was great and the fact that we can adjust the power from high to low was a plus. (I hear people complain that jets blow them http://divxpl.net/error-code/msi-installer-error-codes.html Low Water Flow (LF, FLO), is the usual cause of an overheating (OH, OHH) spa or hot tub. It buzzed for a few minutes. Sign In Sign In Remember me Not recommended on shared computers Sign in anonymously Sign In Forgot your password? Vita Spa Error Codes

Thanks Bob Mark July 16, 2015 at 9:52 pm I have a Vita Spa. It is located on the right side, as you are looking at the spa. If it is hot you have a flow issue, or if it stays hot after the pump is shut off either the pressure switch has stuck close (see FLO error codes Check This Out admin June 7, 2016 at 8:53 am Hi Phil, If you hear the relay kicking but the pump is not engaging the motor could be shot.

But with my experience in such matters I suspect I will again see these warnings. Hydropool Hot Tub Error Codes Gender:Male Posted October 28, 2010 · Report post When the system starts, you will see "Pr" which stands for "Prime", at this point, tap your jets button and prime your pump, He looked into this issue and discovered that this pump is a Vico, and Marquis no longer uses this pump.

It has maintained the temp for 3 days.

He had me Turn off the switch and restart it. Used hot tub tonight, ran jets, when I went to put cover back on I noticed FLO code back on. FINAL NOTE: Balboa M7 systems have the Temperature Sensor as well as the Hi Limit sensor installed in the heater assembly, one at each end. Great Lakes Hot Tub Troubleshooting How to troubleshoot a low flow error So lets say you go out to your hot tub, lift up the cover and you notice the temperature is low and your topside

The error codes above are related to a temperature sensor failure, overheat problems or a flow problem. Powered by Zen Cart. Last week FLO code. this contact form All Products ...

I turned the hot ton on and off again and it was the same thing.